Serproxy seems to work fine and seems to connect to whatever port is. How to find the serial port number on Mac OS X? Read a serial port on Mac OSX Terminal?' Setting up a Serial Console in Mac OS X. On the Mac), or using another machine to connect to the Mac. The serial port using some sort of terminal. Setting up a Serial Terminal with Mac* OS X*. Connect to the USB serial device using the Terminal screen utility by entering the command. Ricardo Wave Full Free here. I looked everywhere on the net to find something that I could afford with which to connect my USB serial port to a Sun machine. I couldn't install Fink or MacPorts, and screen was garbling all of the text for the Solaris install. Finally, I started looking in general UNIX support, which led me to the cu utility.

Starting a Router Terminal Session This section describes how to start a terminal session with the Cisco 1240 Connected Grid Router (CGR 1240 or router) using the console port. Start a terminal session with the router when you are at the router installation location and want to administer the router with a direct connection using the command-line interface (CLI) software. These topics are discussed: ■ ■ ■ ■ Before You Begin Before you start a terminal session with the router, you must connect a PC or PC terminal to the router console port by following the instructions in.

About the Console Port Caution: The console port does not support cable glands. When a cable is connected to this port, the router interior is exposed to environmental elements, which can damage the port and the router interior. This port should be exposed only during terminal sessions, when a cable is connected to the port. This port should never be left unattended when in use.

The console port is an asynchronous serial port that allows you to connect to the device for initial configuration through a standard RS-232 port with an RJ-45 connector. Any device connected to this port must be capable of asynchronous transmission. Console Port Settings Configure the following parameters for the console port: Parameter Console Port Setting Description Baud 9600 Specifies the transmission speed for the connection. Data bits 8 Specifies the number of bits in an 8-bit byte that is used for data.

Parity None Specifies the odd or even parity for error detection. Stop bits 1 Specifies the stop bits for an asynchronous line. Using the Ctrl-C Command The router console port is located on the router exterior and is accessible by removing the seal over the console port (see ). On many Cisco routers, you can enter Ctrl-C to interrupt the router startup process and then delete or change the admin password, or view or delete the router configuration. To prevent unauthorized access to the router configurations and passwords, the Ctrl-C command is disabled on the Cisco CGR 1240 Router while it is booting up and loading the system software.

Connecting to the Console Port with Microsoft Windows To connect to the router console port using Microsoft Windows: 1. Start a terminal emulator application, such as Windows HyperTerminal (included with some versions of Windows OS).

Configure the terminal emulation software with the parameters described in. Connect to the router. Connecting to the Console Port with Mac OS X To connect a Mac OS X system USB port to the console using the built-in OS X Terminal utility: 1. Use the Finder to go to Applications >Utilities >Terminal.

Connect the OS X USB port to the router. Enter the following commands to find the OS X USB port number: macbook:user$ cd /dev macbook:user$ ls -ltr /dev/*usb* crw-rw-rw- 1 root wheel 9, 66 Apr 1 16:46 tty.usbmodem1a21 DT-macbook:dev user$ 4.

Connect to the USB port with the following command followed by the router USB port speed: macbook:user$ screen /dev/tty.usbmodem1a21 9600 To Disconnect the OS X USB Console from the Terminal Window Enter Ctrl+A followed by Ctrl+ Connecting to the Console Port with Linux To connect a Linux system USB port to the console using the built-in Linux Terminal utility: 1. Open the Linux Terminal window. Connect the Linux USB port to the router. Enter the following commands to find the Linux USB port number: root@usb-suse# cd /dev root@usb-suse /dev# ls -ltr *ACM* crw-r--r-- 1 root root 188, 0 Jan 14 18:02 ttyACM0 root@usb-suse /dev# 4. Connect to the USB port with the following command followed by the router USB port speed: root@usb-suse /dev# screen /dev/ttyACM0 9600 To Disconnect the Linux USB Console from the Terminal Window Enter Ctrl+A followed by:, and then type quit.